China high quality Custom Plastic Gears for Toys Cheap Bevel Gear with Good quality

Merchandise Description

custom made plastic gears for toys low cost bevel equipment

Description:

Nylon PA6 Sheets & Rods that made the with 100% Virgin Raw Material by HangZhou Engineering Plastics Industries (Group) Company, has the best performance, such as: very tough, even at low temperatures, and high hardness in the surface, toughness, mechanical lower shock, and abrasion resistance. Combined with these characteristics and good insulation, and chemical properties, it has become common-level materials.
 Its widely used in a variety of mechanical structures and spare parts. Nylon PA6 products that made by HangZhou Engineering Plastics Industries (Group) Company, has the higher hardness, rigidity, a good resistance to wear and heat deflection temperature. 

Positive aspects:

1. Good Tensile strength

two. High impact and notching impact strength

three. High heat deflection temperature 

four. High strength and stiffness

five. Good glide and limp home characters

6. Good chemical stability against organic solvents and fuels

seven. Resistant to thermal aging (applicable temperature between -50°C and 110°C

8. Size alternation by humidity absorption must be considered

 

 

Software:

one. Nylon PA6 Products that made by HangZhou Engineering Plastics Industries (Group) Company is widely substituted for wear parts of mechanical equipment, or used as quick-wear parts of equipment instead of copper and alloy

2. Shaft sleeve, bearing bush, lining, lining plate, gear

3. Worm gear, roller copper guide rail, piston ring, seal ring, slide block

four. Spheric bowl, impeller, blade, cam, nut, valve plate,

5. Pipe, stuffing box, rack, belt pulley, pump rotor, etc.

 

Main Properties of  Nylon 

Property Merchandise No. Unit MC Nylon (Organic) Oil Nylon+Carbon     (Black) Oil Nylon (Green) MC901 (Blue) MC Nylon+MSO2 (Mild black)
Mechanical Qualities one Density g/cm3 1.fifteen one.15 one.a hundred thirty five    1.fifteen one.16
2          Water absorption (23ºC in air) % 1.8-2.     1.8-2. 2 2.3 two.4
3 Tensile power MPa 89 75.three     70     81       78
4 Tensile pressure at split % 29 22.seven 25 35       twenty five
5 Compressive stress(at 2%nominal pressure) MPa 51 51 43 47 forty nine
6 Charpy impact toughness (unnotched) KJ/mtwo No break No split ≥50 No BK No crack
seven Charpy effect energy (notched) KJ/m2 ≥5.seven ≥6.four 4 three.five three.5
8 Tensile modulus of elasticity MPa 3190 3130 3000 3200 3300
9 Ball indentation hardness N/mm2 164 a hundred and fifty a hundred forty five 160 a hundred and sixty
  10 Rockwell hardness M88 M87 M82 M85 M84

 

The lubricating oil external circulation tools of the worm gear reducer gear has reduced oil temperature. The worm gear reducer ideas to traverse its electrical power. The worm gear is created of non-ferrous metal. Learn information worms are usually created of tough steel. Therefore, employing a great deal of warmth in the application, coupled with the affect of the ambient temperature, it is challenging to manage the temperature of the reducer. Use in the temperature selection. When the ambient temperature is reduce than 0℃, the operating temperature of the worm equipment reducer must be managed at -40℃~40℃. It is recommended to warmth or use a minimal freezing point lubricant prior to the oil is completely dissolved.
Specific pitches and leads of the worm do not allow the worm equipment to travel the worm. This is useful when the application wants to lock the output if the software is operating in the reverse direction. When the helix angle is less than 5°, the worm is self-locking. When the helix angle is higher than 10°, the worm can be pushed back. Worm and worm equipment assemblies need to be mounted on vertical, non-intersecting shafts.

China high quality Custom Plastic Gears for Toys Cheap Bevel Gear     with Good quality